High Density Hot Rod Resistance Heating Tube Single Head Cartridge Heater Element For Mould Die
The heating part of the core of the cartridge heater is a nickel-chromium heat-resistant alloy wire, which is wound on a magnesium oxide core rod with excellent insulation and thermal conductivity. The heating wire and the shell are filled with magnesium oxide powder as an insulating material, and the air inside is compressed by the machine to make it into a whole.
After the main body of the cartridge heater is completed, the fixing piece or thread can be installed according to the installation needs. The thread structure of the fixing piece is related to the heating tube installation method. Please contact our sales or technical personnel for the best solution.
Due to the various shapes and specifications, it is impossible to display all of them. If you need to customize various special-shaped heating tubes, please contact customer service.
Product Parameters
1.Diameter 2.Volts and watts 3.Length 4.Type of lead wire 5.Select the outlet method
Main material
Heating wire Ni8Cr20 nickel chromium wire
Insulation filling High purity magnesium oxide powder
Shell (protection tube) SS304,SS310S,SS316,TA1,Incoloy800(NCF800)
Lead Silicone glass fiber (temperature resistance 250ºC)
Teflon (temperature resistance 250ºC)
High temperature glass fiber (temperature resistance 400ºCCeramic beads (temperature resistant to 800ºC)
Lead protection Silicone fiberglass casing, metal braided hose, metal corrugated hose
Sealed end (sealing) Ceramic/ceramic glue (temperature resistant 800ºC)
Silicone rubber (temperature resistant 180ºC)
Resin (temperature resistance 250ºC)
Standard diameter size reference
Diameter in millimeters (mm): 2, 3, 4, 5, 6, 6.5, 8, 9.5, 10, 12, 12.5, 14, 15, 15.8, 16, 18, 19, 20, 25, 30, etc.
Diameter inches (inch): 1/4″, 3/8″, 1/2″, 5/8″, 3/4″, 1″, etc. (Remarks: 1 inch = 25.4 mm)
Note: High-power heating tubes are used in the mold, and mounting holes need to be reserved on the mold according to the size of the cartridge heater (or the outer diameter of the heating tube can be customized according to the size of the mounting hole). Please minimize the size of the heating tube and the mounting hole. Clearance. When machining mounting holes, the unilateral clearance is recommended to be within 0.05mm.
Note: The slash area in the figure represents the heating section of the heating tube
Note: Customize the hole depth of the mold according to the length of the heating part of the cartridge heater
If the hole is too deep, the heating part of the heating tube will be exposed after installation, and there is no good heat dissipation environment, which will damage the heating tube and may even cause accidents such as fire.
If the hole is too deep, the heating tube will be sealed after installation, and the lead part will fall into a higher use environment. Long-term use may cause problems such as a short circuit between the electrodes.
Note: The heating tube should be protected from moisture. It is recommended to start with a low voltage during initial use.
Storage and use in a high-humidity environment will cause the insulation resistance to drop, but after the power is turned on, the moisture in the heating tube will evaporate and the insulation performance will gradually recover. It is recommended to start with a low voltage.
Product laboratory
The mold cartridge heater is a product developed by Super electric heating technology and has undergone many trials and tests.
Each new product developed by Super Electric Heating Technology Company will be tested in our professional laboratory in all aspects of performance, especially the function completion and thermal stability under load conditions.
After the new product is tested, the experimental data is generated. Our engineers analyze the data and then feed the results back to the engineering staff for product optimization to ensure that customers get the product that best meets their expectations.
HOT CORE Heating Technology Co., Ltd. has been specializing in the production of high-density hot bar resistance heating tubes for molds and dies since 1985.which is well-known as one of the leading manufacturers and suppliers of high density hot rod resistance heating tube single head cartridge heater element for mould die. In the past years, we owned strong reputation for the high quality, reliable performance and strong durability of our products. Should you are interested, please feel free to contact our factory.Hot Tags: high density hot rod resistance heating tube single head cartridge heater element for mould die manufacturers, 공급업체, 공장
